CONNECTORS LIST:

last updated March 15, 2008

GRT EIS:
1	gnd		black
2	NC audio out
3	NC
4	NC
5	+12v		red
6	NC
7	warning		violet
8	NC
9	aux4 fuel press	white/brown
10	NC serial in
11	serial out	green/black
12	tach		light green
13	NC reg +12v out
14	fuel flow	green/yellow
15	oil temp	light blue
16	aux6
17	aux5 amps	green
18	oil press	brown
19	coolant temp	yellow
20	aux3 GBT	orange
21	aux2 SCP	white/red	
22	OAT		gray
23	aux1 MAP	green
24	NC
25	reg +4.8v out	dark blue	current sensor & SC press sensor*
* with 475 ohm resistor between 4.8v line SC press sensor (pin 21)


GRT DISPLAY CONNECTOR A (WITH ARINC MODULE)
1	serial out 6			GNS530 P5001-57 & GPSMAP yellow
2	NC serial out 1			reserved for ARINC
3	serial out 5	blue
4	serial out 2	brown		AHRS 5
5	serial out 4			SL30 37-4
					requires BMA/GRT switch
6	LOC dev+ LT in	or/blk		GNS530 P5001-21
7	LOC dev+ RT in	or		GNS530 P5001-22
8	GS dev+down in	gray/blk	GNS530 P5001-28
9	GS dev+ up in	gray		GNS530 P5001-27
10	LOC valid - in	wht/brn		GNS530 P5001-24
11	LOC valid + in	brn		GNS530 P5001-23
12	GS valid - in	wht/grn		GNS530 P5001-30
13	GS valid + in	grn		GNS530 P5001-29
14	power		red		fuse 2 with GRT AHRS power 5a
15	NC power 2
16	NC power 3
17	ground		blk
18	clock power	red/wht		engine bus fuseblock 6
19	serial in 2	yel		AHRS 1
20	NC serial in 1			reserved for ARINC
21	serial in 4	grn/blk		EIS 11
22	serial in 5	gray/red	GNS530 P5001-56 & GPSMAP blue
23	serial in 3	white
24	serial in 6			SL30 37-5
25	serial out 3	black/yel


GRT DISPLAY CONNECTOR B
1	
2	
3	
4	
5	
6	
7	
8	
9	
10	
11	
12	
13	
14	
15	
16	
17	
18	analog in 4*			GNS530 P5001-7
19	analog in 3*			GNS530 P5001-1
20	analog in 2*			GNS530 P5001-2
21	analog in 1*			GNS530 P5006-29
22	
23	
24	
25	
* with 10K pullup resistor to +12v


GRT ARINC-429
1	in 1A				GNS530 P5006-24
2	in 1B				GNS530 P5006-23
3	in 2A				GNS530 P5001-50 & GTX330 P3301-30
4	in 2B				GNS530 P5001-51 & GTX330 P3301-28 
5	out 1A				GNS530 P5001-48
6	shield for in 1			ground only this end of shield
7	shield for in 2			ground only this end of shield
8	shield for out 1		ground only this end of shield
9	out 1B				GNS530 P5001-49


GRT AHRS
1	serial out 1	yellow		display 19
2	serial out 1?
3	serial out 2
4	serial out 2?
5	serial in 1	brown		display 4
6	serial in 2
7	mag Z in	white		mag 2
8	mag Y in	white/brn	mag 1
9	mag X in	white.grn	mag 3
10	NC - OAT
11	NC
12	NC
13	ground		black
14	mag gnd		black		mag 5
15	NC
16	NC
17	NC - test
18	mag ctrl out	white/blu	mag 6
19	NC
20	NC
21	NC
22	mag power out	white/red	mag 4
23	power		red		fuse 2 with GRT DU power 5a
24	NC power 2
25	NC power 3


GRT MAG
1	Y out		white/brn	AHRS 8
2	Z out		white		AHRS 7
3	X out		white/grn	AHRS 9
4	power		white/red	AHRS 22
5	ground		black		AHRS 14
6	control		white/blu	AHRS 18
7	NC
8	NC
9	NC


BMA CPU ANALOG 1  37 pin female  (BMA WON'T MONITOR ENGINE DATA)
1	
2	
3	
4	
5	
6	
7	
8	
9	
10	
11	
12	
13	
14	
15	
16	
17	
18	
19	
20	
21	
22	
23	
24	
25	
26	
27	
28	
29	
30	
31	
32	
33	
34	
35	
36	
37	


BMA CPU ANALOG 2 25 pin female
1	
2	
3	OAT gnd		black
4	
5	
6	
7	
8	
9	
10	
11	
12	
13	
14	OAT +5v out	red
15	
16	
17	
18	
19	
20	
21	
22	
23	OAT signal	yellow
24	
25	


BMA SERIAL 1  9 pin male
1	
2	serial in			SL30 37-5
3	serial out			SL30 37-4
					requires BMA/GRT switch
4	
5	serial gnd
6	
7	
8	
9	


BMA MAG  9 pin male
1	
2	CPU in
3	CPU out
4	
5	gnd
6	
7	
8	
9	+12v to mag


DYNON D-10A
1	master power *			22 RED to fuse 6
2	keep-alive power		22 OR/BLU to E-bus fuse 7
3	master gnd *			22 BLK
4	smart databus A
5	smart databus B
6	NC
7	NC
8	NC
9	serial 1 gnd *			22 GRN/BLK to PC conn DB9-5
10	serial 1 out *			22 YEL to PC conn DB9-2
11	mag out
12	mag power out
13	serial 2 out (encoder)
14	NC
15	backup power
16	smart databus gnd
17	NC
18	audio out
19	NC
20	NC
21	serial 2 gnd
22	serial 1 in *			22 BRN to PC conn DB9-3
23	mag in
24	mag gnd
25	NC - serial 2 in
* required connections


DYNON MAG:
1					BLU/SHLD			
2					YEL
3	
4	
5	
6	
7					RED
8	
9	


DYNON PC CONNECTOR:
1	NC
2	serial in			22 YEL to Dynon pin 10
3	serial out			22 BRN to Dynon pin 22
4	NC
5	ground				22 GRN/BLK to Dynon pin 9
6	NC
7	NC
8	NC
9	NC


GTX 330 transponder:
P3301
1	avionics master on select
	wiring this to power will cause transponder to turn on with power on
2	NC (altitude gray code)
3	NC (altitude gray code)
4	NC (altitude gray code)
5	NC (altitude gray code)
6	NC (altitude gray code)
7	NC (altitude gray code)
8	NC (altitude gray code)
9	NC (altitude gray code)
10	NC (altitude gray code)
11	NC (altitude gray code)
12	external ident select*		grip switch
13	external standby select*	grip switch
14	NC 28v lighting bus hi
15	audio out hi		24 WHT	GMA 340 P1-31 alt warning in 
16	audio out lo		24 WHT/BLU GMA 340 P1-32 alt warning return
17	NC squat switch in
18	NC test mode select
19	altitude alert annunciate*
20	NC
21	power 1	(see 42)		to 5a fuse 14
22	serial in 1			PC software update connector pin 3
23	serial out 1			PC software update connector pin 2
24	serial in 2			Sandia J5-1
25	serial out 2
26	ARINC-429 in 3A
27	gnd	(see 43)		ground plate & PC connector pin 5
28	ARINC-429 out 2B		GRT DU C-4 & GNS530 P5001-51
29	ARINC-429 in 3B
30	ARINC-429 out 2A		GRT DU C-3 & GNS530 P5001-50
31	external suppression I/O
32	ARINC-429 in 1A			GNS530 P5001-46  see 330 manual p.c-9
					??? - C-9 is for dual TXP
33	ARINC-429 in 2A
34	ARINC-429 out 1B
35	ARINC-429 in 1B			GNS530 P5001-47  see 330 manual p.c-9
36	ARINC-429 in 2B
37	ARINC-429 out 1A
38	NC
39	NC
40	NC
41	current temp probe out
42	power 1 (see 21)		to 5a fuse 14
43	gnd (see 27)			ground plate & PC connector pin 5
44	current temp probe in
45	14v lighting bus hi
46	TIS connect select*
47	audio mute select*
48	ARINC-429 in 4A
49	ARINC-429 in 4B
50	NC gray code gnd
51	NC
52	NC
53	NC
54	NC
55	NC
56	NC power 2
57	NC
58	NC
59	NC
60	NC power 2
61	NC
62	switched power out		20 OR to splice: 20 RED to Sandia
					J4-14 and 22 RED/BLU to AIM LEDs +12v
* = ground to activate


GTX330 PC SOFTWARE UPDATE CONNECTOR   (NOT NORMALLY WIRED IN AIRCRAFT)
1	NC
2	serial in			GTX330 P3301-23
3	serial out			GTX330 P3301-22
4	NC
5	gnd				GTX330 P3301-27/43 & gnd plate
6	NC
7	NC
8	NC
9	NC


SL30 nav/comm:
37-PIN REAR PANEL CONNECTION
1	+12v
2	power gnd
3	serial gnd			GROUND PLATE
4	serial in 1			GRT DU A-5 & BMA serial out A-3*
5	serial out 1			GRT DU A-24 & BMA serial in A-2
6	NC
7	**OBS_D (S1) in
8	flip-flop in			grip switch
9	**GSI superflag out
10	**NAV + valid out
11	**+ FROM flag out
12	**+ TO flag out
13	**CDI + RT out
14	**CDI + LT out
15	**back course out
16	**OBS_F (S4) out
17	NC
18	NC
19	**VOR/LOC composite out		
20	audio gnd
21	NC
22	NC
23	nav audio out
24	**OBS_H (R HI) out
25	**OBS_C (R LO) out
26	**OBS_E (S3) in
27	**NAV superflag out
28	**GSI + valid out
29	**NAV - valid out
30	**GSI + up out
31	**GSI + down out
32	**GSI - valid out
33	**ILS energize out
34	**OBS_G (S2) out
35	NC
36	power control out (<50ma)
37	**VOR/LOC composite gnd
* will have to be switched
** NOT USABLE WHILE RS232 USED

SL30 15-PIN COMM INTERFACE
1	+12v
2	NC
3	NC
4	TxKey
5	NC
6	speaker out
7	mic gnd
8	mic 1 in
9	power gnd
10	NC
11	NC
12	intercom select
13	audio gnd input
14	headphone out
15	mic 2 in


GMA 340 audio:
J1  (on RT from back)
1	mkr ant
2	mkr ant return
3	com 3 in
4	com 3 ret
5	com3 mic
6	com 3 key*
7	ADF in
8	ADF ret
9	com 1 in
10	com 1 ret
11	com 1 mic
12	com 1 key*
13	com 2 in
14	com 2 ret
15	com 2 mic
16	MASQ inh*
17	nav 1 in
18	nav 1 ret
19	nav 2 in
20	nav 2 ret
21	DME in
22	DME ret
23	com 3 spkr load
24	com 3 spkr load ret
25	com 1 spkr load
26	com 1 spkr load ret
27	com 2 spkr load
28	com 2 spkr load ret
29	NC
30	com 2 key*
31	alt wrn in***			GNS530 P5001-52
32	alt wrn ret***			GNS530 P5001-53
33	pilot mic in
34	pilot mic key*
35	pilot mic ret
36	ext white lamp A
37	ext blue lamp O
38	ext amber lamp M
39	middle spkr sens
40	pass headset LT
41	pass headset RT
42	pass headset ret
43	tel ringer ret**
44	tel ringer in**
* active low - ground to activate
** inputs for an unswitched radio
*** inputs for an un-muted, unswitched radio
ALL AUDIO JACKS SHOULD BE ELECTRICALLY ISOLATED FROM PANEL


J2  (on LT from back)
1	pilot headset ret
2	copilot headset ret
3	copilot headset LT
4	copilot headset RT
5	14v lgt lo
6	14v lgt
7	14v lgt
8	power
9	power
10	gnd
11	gnd
12	PA mute*
13	ICS mute inhibit*
14	ICS mute inhibit ret
15	high music gain select*
16	pilot headset LT
17	8 ohm select*
18	NC
19	tone enable*
20	swap*
21	swap ret
22	NC
23	music 1 LT in
24	music 1 RT in
25	music 1 ret
26	music 2 LT in (NC)
27	music 2 RT in (DME in)
28	music 3 ret (DME ret)
29	failsafe warn
30	com Tx mute*
31	pilot headset RT
32	copilot mic in
33	copilot mic key*
34	copilot mic ret
35	pass 1 mic
36	pass 1 mic ret
37	pass 2 mic
38	pass 2 mic ret
39	pass 3 mic
40	pass 3 mic ret
41	pass 4 mic
42	pass 4 mic ret
43	speaker ret
44	speaker out
* active low - ground to activate
ALL AUDIO JACKS SHOULD BE ELECTRICALLY ISOLATED FROM PANEL


GNS530W GPS/nav/comm
P5001
1	VLOC annunciate*		GRT DU B-19
2	GPS annunciate*			GRT DU B-20
3	waypoint annunciate
4	terminal annunciate
5	approach annunciate
6	message annunciate
7	OBS annunciate*			GRT DU B-18
8	
9	integrity annunciate
10	
11	
12	
13	
14	ILS/GPS approach
15	NC (secondary power - ties to 72)
16	
17	
18	
19	+12v (5a)  22 AWG
20	+12v (5a)  22 AWG
21	main + left			GRT DU A-6
22	main + right			GRT DU A-7
23	main lateral + flag		GRT DU A-11
24	main lateral - flag		GRT DU A-10
25	main + to
26	main + from
27	main + up			GRT DU A-9
28	main + down			GRT DU A-8
29	main vertical + flag		GRT DU A-13
30	main vertical - flag		GRT DU A-12
31	main OBS rotor C
32	main OBS rotor H
33	main OBS stator D
34	main OBS stator E*
35	main OBS stator F
36	main OBS stator G*
37	
38	
39	lighting bus hi
40	lighting bus lo
41	serial out 3
42	serial in 3
43	
44	
45	
46	GPS ARINC-429 out A		GTX330 P3301-32 see 330 manual p.c-9
47	GPS ARINC-429 out B		GTX330 P3301-35 see 330 manual p.c-9
48	GPS ARINC-429 in 1A		GRT DU C-5
49	GPS ARINC-429 in 1B		GRT DU C-9
50	GPS ARINC-429 in 2A		GRT DU C-3 & GTX330 P3301-30
51	GPS ARINC-429 in 2B		GRT DU C-4 & GTX330 P3301-28
52	TAWS audio out hi
53	TAWS audio out lo
54	serial out 4
55	serial in 4
56	serial out 1			GRT DU A-22 & GPSMAP blue
57	serial in 1			GRT DU A-1 & GPSMAP yellow
58	serial out 2
59	serial in 2
60	NC (gray code)
61	NC (gray code)
62	NC (gray code)
63	NC (gray code)
64	NC (gray code)
65	NC (gray code)
66	NC (gray code)
67	NC (gray code)
68	NC (gray code)
69	NC (gray code)
70	NC (gray code)
71	OBS mode select
72	NC (secondary power - ties to 15)
73	CDI source select
74	
75	
76	
77	gnd  22 AWG
78	gnd  22 AWG
79	
80	
* with 10K pullup resistor to +12v


P5002
1	
2	
3	
4	
5	
6	
7	
8	
9	
10	
11	+12v (10a COM Tx) 18 AWG	18 RED to 10a fuse 24
12	+12v (10a COM Tx) 18 AWG	18 RED to 10a fuse 24
13	
14	
15	
16	
17	
18	
19	
20	
21	gnd 18 AWG
22	gnd 18 AWG
23	
24	
25	


P5006
1	
2	
3	
4	
5	
6	
7	
8	VOR/LOC composite out
9	
10	
11	
12	
13	
14	
15	
16	
17	
18	
19	
20	
21	
22	
23	VOR/ILS ARINC-429 out B		GRT DU C-2
24	VOR/ILS ARINC-429 out A		GRT DU C-1
25	
26	
27	
28	
29	ILS energize*			GRT DU B-21
30	GS + flag
31	GS + down/ - flag
32	GS + up
33	
34	
35	ARINC-429 in B
36	ARINC-429 in A
37	
38	
39	
40	
41	gnd
42	
43	
44	+12v (2a NAV flag)
45	
46	
47	
48	
49	
50	
51	
52	
53	
54	
55	
56	
57	
58	
59	
60	
61	
* with 10K pullup resistor to +12v


GPSMAP 496:
black		ground
red		power
orange		voice -
brown		voice +
yellow		data 1 in		GRT A-1 and GNS530W P5001-57 
blue		data 1 out	GRT A-22 and GNS530W P5001-56 *
white		alarm
violet		data 2 out
green		data 2 in
* Only the GPSMAP or the GNS530 can be installed at any time, or Tx conflict
** SEE SEPARATE DOC ON HOW TO WIRE PORTABLES


PANEL INDICATORS:
1	DVM GND			22 BLK		
2	DVM AUX			22 BLU		
3	DVM MAIN		22 YEL/GRN	
4	EIS WARNING GND		18/20 PURP	
5	LOW FUEL PRESS GND	22 WHT/BLK	
6**	LOW FUEL PRESS +12V	22 WHT/RED	
7	LVAABMM LED GND		22 BLK		
8	LVAABMM LED +12V	22 OR/BLU	
9	AUX FUEL PUMP GND	22 BRN		
10	AUX FUEL PUMP +12V	22 WHT		
11*	LOW FUEL GND		22 BLK		
12**	LOW FUEL +12V		22 RED		
13	LOW FUEL RT PTT		24 OR		
14	LOW FUEL LT PTT		24 OR		
15	LOW FUEL RT +12v	24 RED		
16	LOW FUEL LT +12v	24 RED		
17	LOW FUEL RT LED		24 YEL		
18	LOW FUEL LT LED		24 YEL		
19*	AoA GND			22 BLK		
20	AoA DIMMER (black)	22 BLU		
21	AoA TEST (red)		22 GRN		
22	LOW FUEL RT GND		24 BLK		
23	LOW FUEL LT GND		24 BLK		
24**	EIS WARNING +12V	22 RED/WHT	
25	LO COOLANT SIGNAL - 	22 WHT
26	LO COOLANT SIGNAL + 	22 RED
27	LO COOLANT GND		22 WHT/BLK
28	LO COOLANT +12V		22 WHT/RED
29	SANDIA AIM RED LED	22 RED
30	SANDIA AIM GRN LED	22 GRN
31	SANDIA AIM LEDs +12V	22 RED/BLU
32	SANDIA AIM SW TO UNIT	22 WHT/BLK
33	SANDIA AIM SW TO GND	22 BLK
34	
35	
36	
37	
* tied together to gnd
** tied together to fuse 10


Angle of Attack:
1	gnd
2	+12v
3	DO				display MT2
4	Vcc				display MT4
5	6v				display MT6
6	dimmer (black)
7	flap down switch
8	NC
9	NC (gear down switch)
10	NC
11	NC
12	audio out
13	audio gnd
14	NC
15	CLK				display MT1
16	LD				display MT3
17	display gnd			display MT5
18	display shield
19	NC							  	
20	NC							  
21	PTT (red)						  
22	NC							  
23	NC							  
24	audio shield						  
25	audio 600 ohm


AoA display:
MT1	CLK		orange		CPU DB25-15			 
MT2	DO		blue		CPU DB25-3			 
MT3	LD		green		CPU DB25-16			 
MT4	Vcc		red		CPU DB25-4			 
MT5	display gnd	white		CPU DB25-17			 	
MT6	6v		black		CPU DB25-5			 
shield	gnd				CPU DB25-18				


SANDIA SAE5-35
J4
1	NC (gray code)
2	NC (gray code)
3	NC (gray code)
4	NC (gray code)
5	NC (gray code)
6	AIM strobe/enable*
7	gnd
8	NC			TIED INTERNALLY TO 14
9	NC (gray code)
10	NC (gray code)
11	NC (gray code)
12	NC (gray code)
13	NC (gray code)
14	+12v		20 RED TO SPLICE, THEN 20 OR TO GTX3301-62 
			(SWITCHED POWER) AND 22 RED/BLU TO AIM LEDs
15	gnd		20 BLK, JOINED WITH 22 BLK FROM AIM SW GND
* ground to enable AIM

J5
1	* serial Tx1		26 WHT/BLU	GTX330 P3301-24
2	serial Tx2
3	NC
4	NC RS-232 data mode		leave open for 9600 baud
5	* serial gnd		26 WHT		panel ground
6	* shield gnd		24 BLK
7	AIM set switch (switch provides ground)		22 WHT/BLK
8	AIM set lamp (unit provides ground)		22 GRN
9	AIM altitude lamp (unit provides ground)	22 RED
* shielded twisted pair set
** EFISs get info from 330 ARINC out

AVIONICS FUSE BLOCKS:
1	GRT DU & AHRS		5a	22 RED (2)
2	
3	
4	
5	
6	
7	
8	
9	
10	low fuel/press/EIS warn	5a	3 wires - DB37-6 RED, 
						-12 RED/WHT, -24 WHT/RED
11	low coolant		3a	22 WHT
12	BMA display, CPU	7.5a	18 YEL (2)
13	BMA A/P brkr (10a)	15a	16 LT BLU to breaker
14	GTX 330			5a	22 RED (2)
15	strobe light		15a	16 PURP
16	nav light		10a	18 OR
17	landing light		15a	16 GRAY
18	taxi light		15a	16 RED
19	
20	
21	
22	
23	
24	GNS 530W Comm Tx	10a	18 RED (2)


MAIN FUSE BLOCK:
25	
26	alt field brkr (5a)	7.5a	16 LIME
27	LVAABMM			3a	22 RED/WHT
28	LOVP			3a	20 BLU to 22 RED/GRN & 22 RED/BLU
29	LOVP reset		3a	22 YEL/GRN
30	MT prop ctl brkr (4a)	5a	18 RED/WHT
31	starter			20a	12 PURP
32	
33	
34	
35	
36	acc outlet		15a	16 WHT/RED


ENGINE BUS FUSE BLOCK:
1	ECU			15a	14 WHT/GRN
2	ECU warning		5a	20 RED
3	main fuel pump		20a	14 RED
4	EIS			5a	20 RED
5	aux fuel pump		20a	14 GRN
6	GRT EFIS clock		3a	22 RED/WHT
7	Dynon keepalive		3a	22 OR/BLU
8	SDS injectors		15a	16 RED
9	SDS coils		15a	16 WHT/RED
10	


SDS EM-3/EM-4 J4 WHITE MOLEX CONNECTOR.
8,16     INJECTOR GROUND
4,5,6,7,12,13,14,15 FUEL INJECTOR OUTPUTS
	A	BLK	#1
	B	RED	#3
	C	GRN	#2
	D	WHT	#4
1	FUEL PUMP RELAY		ORANGE
2	FAST IDLE RELAY		BROWN
3	RPM SWITCH RELAY	PURPLE
9	NC			MISC/AUX/CUSTOM/ FUTURE USE.
10	KNOCK SENSOR		YELLOW
11	ECU WARNING		20 PINK    	to panel warning LED (ECU switches to gnd)


25 PIN HARNESS CONNECTOR.
1	+12V SUPPLY				20 RED to 14 WHT/GRN to e-bus
2	+5V POWER FOR THROTTLE POSITION SENSOR	RED
3	+5V POWER FOR MIX KNOB			20 RED
4	+5V POWER FOR MAP SENSOR
5	NOT USED
6	MAP SENSOR SIGNAL			20 WHT
7	AIR TEMP				WHT - color doesn't matter - see 16
8	NOT USED
9	IGN SIGNAL A #1, #2			WHT
10	NC
11	IGN SIGNAL B #3, #4			BLK
12	TACH					20 GRN		to EIS pin 12
13	TACH SIGNAL    "D" SYSTEMS.
14	GROUND FOR MIXTURE KNOB			20 BLK
15	GROUND FOR MAP SENSOR			20 BLK
16	GROUND FOR AIR TEMP SENSOR		BLK - color doesn't matter - see 7
17	GROUND FOR ENGINE TEMP SENSOR		BLK - color doesn't matter - see 20
18	COMPUTER GROUND TO CHASSIS OF VEHICLE	BLK
19	MIX KNOB SIGNAL				WHT
20	WATER TEMP				WHT - color doesn't matter - see 17
21	THROTTLE POS. SIGNAL			
22	NOT USED
23	NOT USED
24	O2 SENSOR				20 GRAY		to PLX signal
25	GROUND					


9 PIN HALL SENSOR PLUG
5	+5V
4	TRIGGER SIGNAL
3	GROUND
9	+5V
8	SYNC SIGNAL
7	GROUND


PLX:
power	RED		tied into +12v to ECU
ground	BLK		tied into GTX330 PC port pin 5 gnd
signal	20 GRAY		to ECU DB25-24


1	
2	
3	
4	
5	
6	
7	
8	
9	
10	
11	
12	
13	
14	
15	
16	
17	
18	
19	
20	
21	
22	
23	
24	
25	
26	
27	
28	
29	
30	
31	
32	
33	
34	
35	
36	
37	
38	
39	
40	
41	
42	
43	
44	
45	
46	
47	
48	
49	
50	
51	
52	
53	
54	
55	
56	
57	
58	
59	
60	
61	
62	
63	
64	
65	
66	
67	
68	
69	
70	
71	
72	
73	
74	
75	
76	
77	
78	
79	
80